嵌入式跑马灯程序

白咱背897keil单片机跑马灯实验报告 -
迟阀褚18467387358 ______ 原发布者:喜欢HQ 学号14142200277序号19单片机原理与接口技术实验报告实验项目序号一实验项目名称跑马灯实验姓名卢志雄专业电子信息工程班级电信14-2BF完成时间2016年4月2日一、实验内容实验内容为3项,其中第1、2项必做.1、...

白咱背897基于verilog语言的跑马灯程序 -
迟阀褚18467387358 ______ module led(clk,rst,led_out); input clk,rst; output [4:0]led_out; reg [30:0]cnt; reg clk_0; reg [4:0]led_out; reg state; always @ (posedge clk_0 or negedge rst) if (!rst) begin state led_out end else case (state) 0:begin led_out state end 1:begin led_out ...

白咱背897编写一个跑马灯程序,用89C51单片机的P1.0到P1.7接八个LED -
迟阀褚18467387358 ______ 注意字符表未经验证, 请自行调试#include #define uchar unsigned char #define uint unsigned int const unsigned char design[16]={0x01,0x02,0x04,0x08,0x10,0x20,0x40,0x80,0x40,0x20,0x10,0x08,0x04,0x02,0x10,0x00}; void delay_1ms(uint x) { ...

白咱背897用keil编写一个跑马灯的程序,要求效果8个跑马灯闪烁五次,然后再循环两圈,接着再闪烁五次后循环两圈 -
迟阀褚18467387358 ______ 害人害到底,帮你写一个吧. ORG 00H AJMP MAIN ORG 30H MAIN: MOV R0,#5 MOV R1,#8 MOV R2,#2 MAIN0: MOV P1,#0 ACALL D05S MOV P1,#0FFH ACALL D05S DJNZ R0,MAIN0 MOV A,#01H MAIN1: MOV P1,A ACALL D05S RL A DJNZ R1,MAIN1 MOV R1,#8 DJNZ R2,MAIN1 AJMP MAIN D05S: MOV R7,#10 MOV R6,#100 MOV R5,#250 DJNZ R5,$ DJNZ R6,$-4 DJNZ R7,$-8 RET END

白咱背89751单片机跑马灯由慢变快,再由快变慢,怎么写程序,我只会写由慢变快的程序 -
迟阀褚18467387358 ______ 就是把speed的“--”变“++”,初值由“10”变“0”嘛,然后来回切换.#define uchar unsigned char #define uint unsigned int#include sbit P10 = P1^0; sbit P11 = P1^1; sbit P12 = P1^2; sbit P13 = P1^3; bit ldelay=0; bit acc=0; uchar speed=...

白咱背897单片机跑马灯程序
迟阀褚18467387358 ______ 您好!根据您的要求,我写了一个程序,我仿真了,可用!你试试吧 org 0000hsjmp ksks: MOV A,#0FFH MOV P1,Azy: MOV R0,#08H MOV A,#0FEHXY: MOV P1,A RL A jnb p3.0,main jnb p3.1,sy LCALL DELAY DJNZ R0,XY sjmp zymain: jnb p...

白咱背897单片机实训—跑马灯程序设计 -
迟阀褚18467387358 ______ LED串470欧电阻接单片机的P1口,改变表中的数,就能改变花样. 参照以下程序: ORG 0000H SJMP START; ORG 0030H; START:MOV R7,#7H;循环次数,寄存器R7送数 MOV A,#00H;累加器置0 MOV DPTR,#TABLE;表首地址 LOOP:...

白咱背897求STC89C52的单片机跑马灯C语言程序 -
迟阀褚18467387358 ______ #include<reg51.h>#define uint unsigned int void delay(int m); void main() { uint temp=0xfe; uint k,i,count; P2=temp; while(1) { while(k<8) { switch(count) {case 0: case 1:delay(50);break; case 2: case 3:delay(25);break; case 4: case 5:delay(100);...

白咱背897求跑马灯的C语言程序 -
迟阀褚18467387358 ______ #include＂reg51.h＂#define uint unsigned intvoid delay(int z){ uint x,y; for(x=z;x>0;x--) for(y=111;y>0;y--);}void main(){ while(1) { P1=0xef; delay(200); P1=0xdf; delay(200); P1=0xbf; delay(200); P1=0x7f; delay(200); P1=0xf7; delay(200); P1=0xfb; ...

白咱背897Java怎么编写走马灯程序 -
迟阀褚18467387358 ______ Java怎么编写走马灯程序代码: package clock; import java.awt.*; import java.awt.event.*; import javax.swing.*; import java.util.Calendar; import java.util.Date; import java.text.*; public class removingLight extends JFrame { public removingLight() { ...